JuniperSRX550防火墙NAT配置-创新互联
一、Source NAT
对于不需要做NAT的网段（比如IPSec×××），需要先关闭这些地址的NAT（如果没有则跳过）
set security nat source rule-set trust-untrust rule no-nat match source-address 192.168.0.0/16
set security nat source rule-set trust-untrust rule no-nat match destination-address 10.10.0.0/24
set security nat source rule-set trust-untrust rule no-nat then source-nat off
对于需要上网或者所有的网段（做地址转换的网段），做source-nat
首先定义一个地址池（要转换的公网地址）：
set security nat source pool natpool1 address 112.48.20.11/32 to 112.48.20.15/32
set security nat source pool natpool2 address 112.48.20.21/32 to 112.48.20.30/32
配置NAT规则匹配源、目、转换地址池
set security nat source rule-set trust-untrust from zone trust
set security nat source rule-set trust-untrust to zone untrust
//匹配特定的地址进行转换（没有特定可省略）
set security nat source rule-set trust-untrust rule nat1 match source-address 0.0.0.0/0
set security nat source rule-set trust-untrust rule nat1 match destination-address 183.253.58.253/32
set security nat source rule-set trust-untrust rule nat1 then source-nat pool natpool1
//默认所有的源、目地址进行转换
set security nat source rule-set trust-untrust rule nat2 match source-address 0.0.0.0/0
set security nat source rule-set trust-untrust rule nat2 match destination-address 0.0.0.0/0
set security nat source rule-set trust-untrust rule nat2 then source-nat pool natpool2
如果NAT地址池有多个地址，除了接口地址，那么其它地址需要做proxy-arp
set security nat proxy-arp interface ge-0/0/0.0 address 112.48.20.11/32 to 112.48.20.15/32
set security nat proxy-arp interface ge-0/0/0.0 address 112.48.20.21/32 to 112.48.20.30/32
做完这些就可以了？ NO！ NO！ NO！防火墙域间策略不能忘
//首先定义两个地址池，并加入到地址组NET中
set security zones security-zone trust address-book address192.168.100.0 192.168.100.0/24
set security zones security-zone trust address-book address192.168.200.0 192.168.200.0/24
set security zones security-zone trust address-book address-setNET address192.168.100.0
set security zones security-zone trust address-book address-setNET address192.168.200.0
//将地址组匹配到trust到untrust的策略中，并放行
set security policies from-zone trust to-zone untrust policy1 match source-addressNET
set security policies from-zone trust to-zone untrust policy1 match destination-address any
set security policies from-zone trust to-zone untrust policy1 match application any
set security policies from-zone trust to-zone untrust policy1 then permit
到此，这192.168.100.0和192.168.200.0就可以通过NAT上网了
二、Destination NAT
部分服务器需要映射到公网去，怎么做呢？那么往下看：
//首先创建要映射的服务器地址池（包括IP地址和端口）
set security nat destination pool1 address 192.168.168.168/32
set security nat destination pool1 address port 443
//创建Destination NAT规则要映射的服务器地址池（包括IP地址和端口）
set security nat destination rule-set desnat from zoneuntrust
set security nat destination rule-set desnatto zone trust
set security nat destination rule-set desnat ruleserver1 match source-address 0.0.0.0/0
//匹配访问112.48.20.2的4430端口转换到内网服务器的443端口
set security nat destination rule-set desnat ruleserver1 match destination-address 112.48.20.2/32
set security nat destination rule-set desnat ruleserver1 match destination-port4430
set security nat destination rule-set desnat ruleserver1 then destination-nat pool 1
还有必不可少的防火墙域间策略
//创建内网服务器地址组及端口
set security zones security-zone trust address-book addressserver1 192.168.168.168/32
set applications application Service_4430 term Service_4430 protocol tcp
set applications application Service_4430 term Service_4430 source-port 0-65535
set applications application Service_4430 term Service_4430 destination-port4430-4430
//创建untrust到trust的策略，目前地址匹配内网服务器地址及端口
set security policies from-zone untrust to-zone trust policy1 match source-address any
set security policies from-zone untrust to-zone trust policy1 match destination-addressserver1
set security policies from-zone untrust to-zone trust policy1 match application Service_4430
set security policies from-zone untrust to-zone trust policy1 then permit
至此，外网就可以使用http://112.48.20.2:4430/访问内网的服务器了
还有一个问题，此时内网的用户却不能使用这个公网地址访问内部的服务器，这个需要在NAT上再做一个内部的地址转换，如下：
//创建一个源地址映射的地址池（内部服务器映射的地址）
set security nat source pool sorpool4 address 112.48.20.2/32
//创建trust到trust的策略如下
set security nat source rule-set trust-trust from zone trust
set security nat source rule-set trust-trust to zone trust
set security nat source rule-set trust-trust ruleserver1 match source-address 0.0.0.0/0
set security nat source rule-set trust-trust ruleserver1 match destination-address192.168.168.168/32
set security nat source rule-set trust-trust rule server1 match destination-port443
set security nat source rule-set trust-trust rule server1 then source-nat pool sorpool4
至此，内网也可以通过公网地址访问内部服务器了！！！
如有雷同，纯属巧合，欢迎指正！
另外有需要云服务器可以了解下创新互联cdcxhl.cn，海内外云服务器15元起步，三天无理由+7*72小时售后在线，公司持有idc许可证，提供“云服务器、裸金属服务器、高防服务器、香港服务器、美国服务器、虚拟主机、免备案服务器”等云主机租用服务以及企业上云的综合解决方案，具有“安全稳定、简单易用、服务可用性高、性价比高”等特点与优势，专为企业上云打造定制，能够满足用户丰富、多元化的应用场景需求。
当前标题：JuniperSRX550防火墙NAT配置-创新互联
URL分享：http://ybzwz.com/article/pocoi.html
