BGP团体属性（实验）
根据BGP路由的团体属性设置BGP路由策略
成都创新互联公司是工信部颁发资质IDC服务器商，为用户提供优质的服务器机柜租用服务
R1配置：
Loopback0 1.1.1.1
Loopback1 192.168.1.1/24
Loopback2 192.168.2.1/24
Loopback3 192.168.3.1/24
Loopback4 192.168.4.1/24
E1/0 10.1.12.1
R2配置：
Loopback 2.2.2.2
E1/0 10.1.12.2
配置IGP（RIP）保持连通性：
R1配置：
router rip
version 2
network 1.0.0.0
network 10.0.0.0
network 192.168.1.0
network 192.168.2.0
network 192.168.3.0
network 192.168.4.0
no auto-summary
R2配置：
router rip
version 2
network 2.0.0.0
network 10.0.0.0
no auto-summary
开始配置BGP(EBGP)：
R1
router bgp 109
bgp router-id 1.1.1.1
bgp log-neighbor-changes
network 1.1.1.1 mask 255.255.255.255
network 10.1.12.0 mask 255.255.255.0
network 192.168.1.0
network 192.168.2.0
network 192.168.3.0
network 192.168.4.0
neighbor 10.1.12.2 remote-as 110
R2
router bgp 110
bgp router-id 2.2.2.2
bgp log-neighbor-changes
network 1.1.1.1 mask 255.255.255.255
network 10.1.12.0 mask 255.255.255.0
neighbor 10.1.12.1 remote-as 109
neighbor 10.1.12.1 route-map set_local_pref in
R2#sh ip bgp
BGP table version is 7, local router ID is 2.2.2.2
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.1/32 10.1.12.1 1 32768 i
*> 10.1.12.0/24 0.0.0.0 0 32768 i
*> 192.168.1.0 10.1.12.1 0 200 0 109 i
*> 192.168.2.0 10.1.12.1 0 200 0 109 i
*> 192.168.3.0 10.1.12.1 0 150 0 109 i
*> 192.168.4.0 10.1.12.1 0 150 0 109 i
R1配置团体属性
第一步：开启路由器支持团体属性
ip bgp-community new-format
第二步，配置prefix-list列表
ip prefix-list 1permit 192.168.1.0/24
ip prefix-list 1 permit 192.168.2.0/24
ip prefix-list 2permit 192.168.3.0/24
ip prefix-list 2permit 192.168.4.0/24
第三步，配置route-mapset_community
route-map set_community permit 10
match ip address prefix-list 1
set community 109:1
route-map set_community permit 20
match ip address prefix-list 2
set community 109:2
第四步，在BGP当中调用
neighbor 10.1.12.2 send-community
neighbor 10.1.12.2 route-map set_community out
R2上配置route-mapset_local_pref，对R1传递过来的带有团体属性的路由进行匹配，并附上特定的local-preference
第一步：开启路由器支持团体属性
ip bgp-community new-format
第二步：设置团体属性列表
ip prefix-list 1 seq 5 permit 192.168.2.0/24
ip prefix-list 1 seq 10 permit 192.168.4.0/24
第三步：
route-map set_local_pref permit 10
match community 1
set local-preference 200
route-map set_local_pref permit 20
match community 2
set local-preference 150
第四步：在BGP当中调用route-mapset_local_pref
neighbor 10.1.12.1 route-map set_local_pref in
验证配置：
R2#sh ip bgp
BGP table version is 7, local router ID is 2.2.2.2
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.1/32 10.1.12.1 1 32768 i
*> 10.1.12.0/24 0.0.0.0 0 32768 i
*> 192.168.1.0 10.1.12.1 0 200 0 109 i
*> 192.168.2.0 10.1.12.1 0 200 0 109 i
*> 192.168.3.0 10.1.12.1 0 150 0 109 i
*> 192.168.4.0 10.1.12.1 0 150 0 109 i
R2#sh ip bgp 192.168.1.0
BGP routing table entry for 192.168.1.0/24, version 2
Paths: (1 available, best #1, table default)
Not advertised to any peer
Refresh Epoch 1
109
10.1.12.1 from 10.1.12.1 (1.1.1.1)
Origin IGP, metric 0,localpref 200, valid, external, best
Community: 109:1
rx pathid: 0, tx pathid: 0x0
从R1学来的团体属性为Community: 109:1的路由设置本地优先级为200.
R2#sh ip bgp 192.168.3.0
BGP routing table entry for 192.168.3.0/24, version 4
Paths: (1 available, best #1, table default)
Not advertised to any peer
Refresh Epoch 1
109
10.1.12.1 from 10.1.12.1 (1.1.1.1)
Origin IGP, metric 0, localpref 150, valid, external, best
Community: 109:2
rx pathid: 0, tx pathid: 0x0
从R1学来的团体属性为Community: 109:2的路由设置本地优先级为150.
没有被匹配的路由还是以默认值传递。
分享标题：BGP团体属性（实验）
转载注明：http://ybzwz.com/article/pesoii.html
